Current Location: Home >> Products >> Scissor Jack

2 Ton Scissor Jack

  • Model:T10202-GS
  • Capacity:2 Ton

• Quickly & easily change your tire.

• Compact design

• Collapsible and easy to store in your car or garage.

• Wide base and saddle provides stability under load.

• Constructed of heavy duty steel

• Use for most cars for tire removing.

Product Information | Product Parameters | Features | Common Problems And Solutions
Product Information

This collapsible, compact steel scissor jack can be used as a rugged replacement    

 jack or an extra utility jack that can be stored in the trunk of your car. The extra-wide base offers easy positioning, and the one-piece handle delivers on-the-spot quick response and speed when you need it.




public-详情图片.jpg

Product Parameters

Model

T10202-GS


Capacity

2 Ton

Min. Height

120 mm


Max Height

395 mm

Total Length

450 mm


Stroke With Rated load

260-390 mm

N.W./G.W.

3.5/4 kg


Package Size

660x470x260 mm

QTY/CTN

10 PCS


QTY/20'CY

4800 PCS

Features

• Quickly & easily change your tire.

• Compact design

• Collapsible and easy to store in your car or garage.

• Wide base and saddle provides stability under load.

• Constructed of heavy duty steel

• Use for most cars for tire removing.


Common Problems And Solutions

If you use and maintain your equipment properly, it will give you many years of service. Follow the

maintenance instructions carefully to keep your equipment in good working condition. Never perform any

maintenance on the equipment while it is under a load.

Inspection

You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components

function before each use. Follow lubrication and storage instructions for optimum product performance.

Binding

If the product binds while under a load, use equipment with equal or a larger load capacity to lower the load

safely to the ground. After un-binding; clean, lubricate and test that equipment is working properly. Rusty

components, dirt, or worn parts can be causes of binding Clean and lubricate the equipment as indicated in

the lubrication section. Test the equipment by lifting without a load. If the binding continues contact Customer

Service.

Cleaning

If the moving parts of the equipment are obstructed, use cleaning solvent or another good degreaser to clean

the equipment. Remove any existing rust, with a penetrating lubricant.

Lubrication

This equipment will not operate safely without proper lubrication. Using the equipment without proper

lubrication will result in poor performance and damage to the equipment. Some parts in this equipment are not

self-lubricating inspect the equipment before use and lubricate when necessary. After cleaning, lubricate the

equipment using light penetrating oil, lubricating spray.

Use a good lubricant on all moving parts.

For light duty use lubrication once a month.

For heavy and constant use lubrication recommended every week.

NEVER USE SANDPAPER OR ABRASIVE MATERIAL ON THESE SURFACES!

Rust Prevention:

Check rams and pump plungers on the power unit assemblies daily for any signs of rust or corrosion.

Without a load lift the equipment as high as it goes and look under and behind the lifting points. If signs of rust

are visible clean as needed.

Grease Fittings

Some models contain grease fittings the will regularly need to be greased and lubricated.

Storing the Jack

1. Lower the Lifting Arm.

2. Place the handle in the upright position.

3. Store in a dry location, recommended indoors.

Note: If the jack is stored outdoors, be sure to lubricate all parts before and after use to ensure the jack stays

in good working condition. Always store jack in the fully retracted postion when stored in outdoor or caustic

enviroments that can cause corrosion and/or rust.



Our Phone

Hotline

400-066-4786

Feedback
Contact
Telephone
Fill in your message
Tongrun WeChat

ewm2.jpg

Follow The Dynamic

Company Address

江苏省常熟市经济技术开发区

新龙腾工业园